ASTM D3654 PDF

ASTM D – Designation: D /D M – 06 Standard Test Methods for Shear Adhesion of. ASTM D/DM: Standard Test Methods for Shear Adhesion of Pressure- Sensitive Tapes. A summary of ASTM standards relating to pressure sensitive tape is attached. The shear test procedures are also harmonized: ASTM D and PSTC.

Author: Najinn Kekus
Country: Malaysia
Language: English (Spanish)
Genre: Music
Published (Last): 20 September 2016
Pages: 320
PDF File Size: 15.82 Mb
ePub File Size: 16.29 Mb
ISBN: 537-8-79168-930-1
Downloads: 7778
Price: Free* [*Free Regsitration Required]
Uploader: Goltikus

ASTM D shearing tester is for the test of lasting adhesive of pressure sensitive adhesive tapes, labels and other interrelated products. Between laboratories Between testers Between rolls Residual 0.

Link to Qstm This link will always route to the current Active version of the standard. Where width or other factors causing high adherence to backing make it impossible to remove the specimen at the prescribed awtm, remove it at a rate as close to aztm [30 in. A standard mass is attached to the free end of the tape and allowed to act for a speci?

The edges shall be separated by 12 6 0. It is common to test at least? Width of specimen for Procedures E, F, and G if other than 12 mm [0.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory ast, prior to use. We have no amendments or corrections for this standard. The test plate with adhesive specimen is vertically hanged on the stand and its bottom is attached with a standard weight. For Procedures A and H, substitute steel panel instead of?

Test specimens should be taken from several rolls of a tape and, whenever possible, among several production runs of a tape. Transport of foodstuffs or medical; warmth or cold Available in compartment simple, double or icebox typify Isothermal boxes icebox for two wheels, scooters, motorcycles typify Identification number of the aatm Equipment d365 Search in a category: This standard is subject to revision at any time by the responsible technical committee and must be reviewed every?

  INGRID RIMLAND LEBENSRAUM PDF

For Procedures A, E, and H three replicate specimens shall be averaged in accordance with Section 11 for each test result. Allow the remaining mm [8 in.

Record the time elapse in which the tape specimen has completely separated from the test panel. A number in parentheses indicates the asrm of last reapproval. Between uses, the panels test surface shall be protected from scratches and contamination, and the panels stored at conditions described in 8.

During storage, panels zstm be protected from damage or contamination. The values stated in each system are not be exact equivalents; therefore, each system shall be used independently of the other. The mass of the roller shall be 6 45 g [4.

The assessment may be within a roll of tape, between rolls or production lots. By navigating on this website, you accept their use. The surfaces of similar fiberboards may exhibit considerable variation between d33654, between batches from one mill, and within batches.

You may delete a document from your Alert Profile at any time. This may be used to compare the shear adhesion of a tape to a particular? Examples of averages and with-in-roll standard satm including test error are as follows: One company reports that, with care, the between laboratory standard deviation and the residual including within roll standard deviation may be higher d36654 lower than reported here, depending on the tape type and manufacturer.

Summary of Test Method 3. No single value shall be considered as representative of the roll under test.

  AGENDA ELECTRICIANULUI MOELLER PDF

ASTM D/DM – 06() – Standard Test Methods for Shear Adhesion of Pressure-Sensitive Tapes

The assessment may be within a roll of tape, between rolls or production lots. Standards Subsctiption may be the perfect solution. For Procedures E, F, and G the amount of slippage in mm [in. Roll down the test area twice in each lengthwise direction with the rubber-covered steel roller described in 5.

The razor shall be held in position using side plates.

China Supplier ASTM D3654 Polymide Tape Lasting Adhesive Test Meter

The adequate solution for the transport of your fresh products or frozen food or of your organic and The tape must be at a true right angle to the bent Combining values from the two systems will result in non-conformance with the standard. Proceed to Checkout Continue Shopping. This standard has been approved for use by agencies of the Department of Defense.

Procedure H may be used to compare the shear adhesion of tape applied to a standard steel surface and tested at an elevated temperature. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.

ASTM D | Rycobel

A superscript epsilon e indicates an editorial change since the last revision or reapproval. To be suitable, materials must be lint free during use, absorbent, contain no additives that are soluble in the solvents listed in 6. Record the time elaspe in which the tape specimen has separated completely from the test panel see Fig.