FIDC tracking water injection system osa User manual v4w Page 2 GETTING TO KNOW THE AQUAMIST HFS-6 osa Aquamist has been. WORKS has been using Aquamist Water Injection since We have seem them all since then and still strongly believe these are the most well thought out. Retired System Information. Below you will find technical info and original sales info for the systems. Aquamist HFS-6 Injection System. Aquamist HFS
|Published (Last):||13 May 2014|
|PDF File Size:||7.92 Mb|
|ePub File Size:||8.32 Mb|
|Price:||Free* [*Free Regsitration Required]|
It just cannot be simpler for the user. The system provides a pre-pressurized water line up to 8 bars and the flow rate is metered by our latest High aqhamist Valve HSV.
The ERL electro-magnetic pump In order to find a pump that will reliably perform under the harsh environment of the engine bay, we have no alternatives but to design our own. See full item description.
Retired System Information
The ERL electro-magnetic pump is the result of a two-year intense mechanical and electronic research and development program. Two colored LEDs are mounted on the top side of the box. Delivery time is estimated bfs-6 our proprietary method which is based on the buyer’s proximity to the item location, the gfs-6 service selected, the aquamiist shipping history, and other factors. Sell one like this.
RACE PUMP INFO We have ruled out the widely available centrifugal pump as the pumping mechanism, because it is always coupled to a high rotational-speed drive-motor for efficiency reasons, hence it is prone to wear; further problem arises when the water inside the pump is frozen, the drive hds-6 has to be detached from the vane by a slipping clutch arrangement so drive-motor windings cannot be damaged as a result of jamming, this led to unnecessary expenses and complicated mechanical links.
Back to home page Return to top. Estimated on or before Mon. Developed with years of experience in World Rally Championship racing and feedback from the industry by the most demanding users, the HFS-6 surpasses all other systems in operation, performance, and reliability. As usual, except for the water tank, the system is supplied with everything needed to be fitted with ease.
It is normally fitted to the vacuum side of the inlet asuamist 2D mode for applications where load signal throttle angle sensor or manifold absolute pressure sensor MAP sensor is available.
This amount is subject to change until you make payment.
Aquamist 2s The 2s is a fully-mappable water-injection system, is pre-pressurizedequipped with diagnostic circuitry, able to detect blocked water-jet and abnormal operation problems. Sep 20, Add to watch list.
Delivery times may vary, especially during peak periods. The water-pump is activated when an adjustable pressure switch, fitted to the inlet manifold, reaches its preset point: Water is then delivered without being in contact with the drive-motor, pressure and delivery rate is regulated by internal high-tech electronic circuitry. The special magnetic stainless armature is set in motion by strong magnetic field induced by a powerful solenoid. Thread size of the jet is M8x0.
For those who want a 3-D water injection MAP but do not want to spend the time-consuming task of mapping, this system is perfect for you.
Water travels through these grooves, acquiring a swirling motion before leaving the small hole on the tip: A high pressure pump with NO mechanical links, thus eliminated damages caused by jamming. Aquamist 1s The 1s is a single stage system that consists of an ERL high-pressure electro-magnetic water pump, adjustable pressure switch, plus all the necessary hardware to form the basis of a starter kit.
An additional pair of wires supplies a stablised output voltage of 5 volts for driving a MAP manifold absolute pressure sensor. For applications where load signal throttle angle sensor or manifold absolute pressure sensor MAP sensor are available, the MF2 can hcs-6 these signals and perfom 3-D mapping functions. Below you will find technical info and original sales info for the systems. As the pulsed signal from the pressure fhs-6 is directly proportional to the flow of water, it can either be recorded by an hfw-6 data acquistion system for diagnostic purposes or read by the control ECU to monitor blockage or water jet and other faults that may arise.
The new design aquamizt also one of the easiest to install as well. Aquamist 2c The 2c is designed for stand-alone EMS systems. Seller assumes all responsibility for this listing.
There are two additional inlet ports: The MF2 uses incoming RPM and pressure signals from the sensors in the engine bay and compares them with a pre-programmed map set by the user.
It is normally fitted to the vacuum side of the inlet manifold 2D mode. The valve is terminated with water proof sealed connectors IP Add to watch list Add to wish list.
Back to home page. As seen form the diagram above, the construction of the center of the pump is very similar to a bicycle pump, two valves: San Diego, Aquxmist, United States.
The inline valve is made of high grade stainless steel and capable of achieving a cycling rate of over Hz. Peak pressure can go as high as psi!
Email to friends Share on Facebook – opens in a new window or tab Share on Twitter – opens in a new window or tab Share on Hfw-6 – opens in a new window or tab Add to watch list. Jet sizes from 0.