ALLEN BRADLEY 1305 VFD MANUAL PDF

However, using an Allen-Bradley motor with your drive removes the . Н Installation guidelines called out in Appendix D of the User’s Manual. Installation Instructions IN. May, Allen-Bradley. Dynamic Brake. Cat. No. KAA KBA03, KBA06, KBA Table of Contents. Find great deals for Allen Bradley Adjustable Frequency AC Drive User Manual. Shop with confidence on eBay!.

Author: Zologrel Nashicage
Country: Jamaica
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 14 November 2012
Pages: 176
PDF File Size: 11.78 Mb
ePub File Size: 9.51 Mb
ISBN: 460-8-62778-688-1
Downloads: 43329
Price: Free* [*Free Regsitration Required]
Uploader: Taura

1305 AC Drives

Check for excess load, improper DC boost setting, DC brake volts set too high or other causes of excess current. Fast repairs at low costs. Drive Reset Fault – F22 May occur on power-up. Phase U Fault – F38 A phase to ground default has been detected between the drive and motor in this phase.

Error 2 – The number of parameters in saved profile does not equal master number. The Adjustable Frequency AC drive is available with ratings 0. A longer acceleration tiime or a lighter load may be required.

Allen Bradley Adjustable Frequency AC Drive User Manual | eBay

DC Bus voltage fell below the minimum value. Inspect for proper mounting and spacing. Inspect to ensure that the ambient temperature limit has not been exceeded. Inspect for blocked or contaminated heat sink fins. Unplug the HIM from the cable or drive, then reconnect it. Reset to Default Parameters and Cycle power.

  DISTRESSOR MANUAL PDF

Motor Stall Fault – F6 The motor has stalled If the motor is drawing excessive current, the motor load is excessive and will not allow the drive to accelerate to set speed. Check for broken wires, loose connections, or transducer loss at mA input, TB2.

Overcurrent Fault – F12 Overcurrent is detected in overcurrent hardware trip circuit. Check the external potentiometer circuit at TB2, terminals 1, 2, and amnual for a disconnected current.

The last parameter programmed will be displayed on the top line. Open Pot Fault – F9 An external pot is connected and the ground lead of the pot is disconnected, creating a potential drive overspeed hazard. An external pot is connected and the ground lead of the pot is disconnected, creating a potential drive overspeed hazard.

The Adjustable Frequency AC Drive is a variable speed drive designed to control the speed of three-phase AC induction motors in a variety of demanding applications where flexibility, performance and ease of use ffd essential.

D Micro Programmable Logic Controllers.

Allen Bradley 1305 Adjustable Frequency AC Drive User Manual

Please select the Repairs tab for more information or to request a quote. DC Braking cannot be used allem a synchronous motor.

Check the motor and external wiring to the drive output terminals for a shorted condition.

Phase W Fault – F40 A phase to ground fault has been detected between the drive and motor in this phase. Save a new profile. Check motor for grounded phase.

  LAGUNE 2 GLOSARIO PDF

Verify that the parameter has been programmed correctly. Check the AC line for high manial voltage or transient conditions. Inspect the wiring between the drive and motor.

If the motor is drawing excessive current, the motor load is excessive and will not allow the drive to accelerate to set speed.

Check for proper mounting and spacing. If not, manually program any remaining parameters. Check programming of [Curr Lim Trip En] parameter. Press Enter to continue download.

Reprogram Fault – F48 May occur when drive parametersare reset to default settings. Verify that all parameters have been programmed. Change [Cable Length] to “Long” if applicable.

Allen Bradley Adjustable Frequency AC Drive AB

Connect proper adapter or change active frequency source. Serial Fault – F10 An active local bus adapter is disconnected while it possesses control of a local bus function.

Extend the deceleration time or instal dynamic brake option. Check for external noise sources. May occur on power-up. Replace the Communication cable.